Manufacture of metal gates
Metal gates are well suited for installation on any territory, both industrial and private. They have been occupying a leading position in the niche of the most popular types of gates for many years and, thanks to their qualities, continue to keep this brand.
Modern metal gates have a lot of positive characteristics, among which are corrosion resistance, a high level of noise and thermal insulation, as well as resistance to moisture. Any type of this structure, which will function with the help of electricity, can be made of metal. At the same time, we can say for sure that this material is the best material, since it fully meets most of the requirements, varying from the type of this design.
The production of steel gates of the roll type (roller shutters, roller shutters, shutters) is more complex than sliding and sectional gate systems. The rolled web consists of separate lamellae, which are interconnected by locks. Lateral displacement is prevented by plastic or metal side locks. It is possible to manually and automatically control the lowering and lifting of the roller shutter. The main advantage of this design is its small dimensions and the minimum necessary space for installing the mechanism. Vertical lifting of the gate leaf is convenient in winter - there is no need to clear a large space before driving from snow. Steel roller gates can be used for private purposes - garages, tents, private houses and industrial purposes - production, parking lots, shops. The main difference between roller shutters and gates:
![The inside of the roll gate box Внутренности короба рулонных ворот]()
The manufacture of metal gates, which belong to the swing type, implies the presence of two flaps that are attached to pre-installed pillars, to which the electric drive is subsequently attached. In one of these doors, you can build a gate. The very manufacture of this design, as a rule, begins with the sheathing of steel profiles with metal sheets or profiled sheets, this option is more budget-friendly.
The production of metal gates belonging to the sliding type occurs a little differently. The canvas is made according to the same principle as in the case of swing gates. The canvas can, if desired, be sheathed with profiled sheets only on one side or on both sides. The length of the web should be the same as that of the opening, plus half should be left on the cantilever part of this product, which in turn performs the supporting function of the web. Therefore, the highest requirements are put forward for the installation of sections on which special roller fasteners are placed.
Types of metal gates
The production of steel gates of the roll type (roller shutters, roller shutters, shutters) is more complex than sliding and sectional gate systems. The rolled web consists of separate lamellae, which are interconnected by locks. Lateral displacement is prevented by plastic or metal side locks. It is possible to manually and automatically control the lowering and lifting of the roller shutter. The main advantage of this design is its small dimensions and the minimum necessary space for installing the mechanism. Vertical lifting of the gate leaf is convenient in winter - there is no need to clear a large space before driving from snow. Steel roller gates can be used for private purposes - garages, tents, private houses and industrial purposes - production, parking lots, shops. The main difference between roller shutters and gates:
- The maximum dimensions of the canvas - gates are made up to 9 meters wide, and shutters are only up to 5 meters;
- Burglar resistance- industrial variants, as a rule, have thicker and stronger lamellas, and this results in increased resistance to burglary and damage;
- Reliability of all parts - the resource of the mechanism for the private sector does not provide for intensive use, plastic and inexpensive components are used. Industrial variants have a longer service life and more reliable components.
The manufacture of metal gates, which belong to the swing type, implies the presence of two flaps that are attached to pre-installed pillars, to which the electric drive is subsequently attached. In one of these doors, you can build a gate. The very manufacture of this design, as a rule, begins with the sheathing of steel profiles with metal sheets or profiled sheets, this option is more budget-friendly.
The production of metal gates belonging to the sliding type occurs a little differently. The canvas is made according to the same principle as in the case of swing gates. The canvas can, if desired, be sheathed with profiled sheets only on one side or on both sides. The length of the web should be the same as that of the opening, plus half should be left on the cantilever part of this product, which in turn performs the supporting function of the web. Therefore, the highest requirements are put forward for the installation of sections on which special roller fasteners are placed.